This type of centrifugal machine is developed on the basis of centrifugal machine model SS.In addition to the advantages of model SS, labor power is greatly reduced, the unloading is rapid, it is easy to clean, so the efficiency is increased, pollution to the finished products is therefore avoided.It is used for separation of floating liquid with high loose type solid-phase, average size fineness, not easy to compress, need washing, liquid phase with relatively small viscosity.It is widely used in the industries of chemicals, pharmacy, food, light industry, minerals, environment protection etc.The machine corresponds to GMP series design.

Electric motor drives revolving drum to revolve at a high speed by clutch¡ê?material is added from the head of revolving drum.liquid phase discharges through filter cloth and filter opening in the drum wall, solid phase is left in the revolving drum. Open the cover and loosen the adjusting pin of liquid preventing broad when the machine is stopped. Liquid preventing broad and filter bag with filter residue inside are hung to discharge pit by lifting appliance. Loosen the hanging leg and open filter bag, filter bag will fall to the ground.

Structural diagram of model SD centrifuge

1.Triangular belt base	2.Zoccola	3. Water outlet	4.Bottom head	5.Chassis
6.Brake bar	7.Bearing block	8 Revolving drum	9.Filter bag	10.Principal axis
11.Adjusting pin	12. Liquid preventing board	13.Split flange cover	14.Hanging leg	15.Spacer
16.Hanging hook	17.Lazy arm	18.Discharge handle	19.Locked shaft	20.Lifting appliance
21.Full open type cover	22.Feed pipe	23.Bear frame	24.Electric motor	25.Triangular belt

Main specification and technical index

Type	Number of revolutions						Power of electric machine kw	Maxi-mumsepa- ration factor	Weight of the whole machinekg	External dimensions (Length Width height) mm	Limit height for opening covermm
	Diameter mm	Height mm	caliber of liquid preventing board mm	Rotating speed r/min	Working volumeL	Maximum weight of discharge kg
SD800	800	400	560	0-1500	100	135	7.5	1007	1450	19501380 1150	2280
SD1000	1000	450	720	0-1200	145	200	11	805	2300	21501550 1250	2590
SD1200	1200	500	900	0-800	250	300	11	430	2500	23001700 1250	2760
SD1250	1250	500	950	0-950	280	400	18.5	631	3800	23501750 1300	2850
SD1500	1500	550	1100	0-850	500	650	22	606	4800	27501870 1520	3400

Foundation drawing of Model SD Centrifuge

Main innstallation dimension (unit:mm)

Type	A	B	C	D1	D2	D3	E	F	R	M	L
SD800	360	120	400	1247	1200	900	400	100	150	20	500
SD1000	400	120	400	1443	1320	950	400	100	158	22	500
SD1200	450	130	470	1617	1550	1100	470	120	150	22	600
SD1250	475	130	550	1617	1600	1150	550	130	150	24	600
SD1500	500	200	650	2032	1750	1400	650	150	160	24	700

Guide for placing order

Material: Stainless steel, titanium alloy, carbon steel etc.
Types of machine cover:split flange and full open, spliet flange is easy to open and close while full open can meet the requirement of obturation.
Driving means : Electromagnetism speed control can realize the requirements of low speed feeding and high speed separation. It is applicable to the separation of many kinds of materials¡ê?frequency control explosibility separation motor drive is accordance with GMP requirements.

Note: The above technical parameter should refer to the product operation instructions. This product is covered with responsibility risk of PICC